An Overview of Methods using Reduced-Ordered Transformation Matrices for Fault-Tolerant Control of 5-phase Machines with an Open Phase | Vu, Duc Tan
/5

0 avis

An Overview of Methods using Reduced-Ordered Transformation Matrices for Fault-Tolerant Control of 5-phase Machines with an Open Phase

Archive ouverte : Communication dans un congrès

Vu, Duc Tan | Nguyen, Ngac Ky | Semail, Eric

Edité par HAL CCSD ; IEEE

International audience. This paper studies control strategies using modified transformation matrices when five-phase machines operate in oneopen-phase faults. The basic idea of these methods is to maintain the rotating field under asymmetrical conditions as the same as in healthy condition by determining new transformation matrices. The dimension of the new matrices is equal to the number of remaining healthy phases in post-fault conditions. There have been different ways to determine the new transformation matrices applied for different types of five-phase machines in recent decades. In this study, an overview and analyses on these methods will be presented. In addition, advantages and drawbacks of these control strategies are clarified by numerical results.

Consulter en ligne

Suggestions

Du même auteur

Fault-tolerant control of non-sinusoidal multiphase permanent magnet synchronous machine drives under constraints on current and voltage for automotive applications. Commande tolérante aux défauts des entraînements de machines synchrones à aimants permanents polyphasées non-sinusoïdales sous contraintes de courant et de tension pour les applications automobiles | Vu, Duc Tan

Fault-tolerant control of non-sinusoidal multiphase permanent magnet synchr...

Archive ouverte: Thèse

Vu, Duc Tan | 2020-11-24

Electric drives for electrified vehicles need to fulfil some specific requirements from automotive markets such as high efficiency, high volume power and torque densities, low-cost but safe-to-touch, high functional reliability, h...

Fault-tolerant Control for Non-sinusoidal Multiphase Drives with Minimum Torque Ripple | Vu, Duc Tan

Fault-tolerant Control for Non-sinusoidal Multiphase Drives with Minimum To...

Archive ouverte: Article de revue

Vu, Duc Tan | 2021-12-09

International audience. For non-sinusoidal electromotive force (NS-EMF) multiphase machines, this paper proposes a new strategy and control scheme to guarantee smooth torque under an open-phase fault. Notably, the c...

Eliminations of Low-frequency Current Harmonics for Five-phase Open-end Winding Non-sinusoidal Machine Drives applying Neural Networks | Vu, Duc Tan

Eliminations of Low-frequency Current Harmonics for Five-phase Open-end Win...

Archive ouverte: Communication dans un congrès

Vu, Duc Tan | 2020-10-18

International audience. This study aims at eliminating unwanted harmonics in current control of a five-phase non-sinusoidal permanent magnet synchronous machine (PMSM) in an open-end winding configuration. The machi...

Du même sujet

Open-Phase Fault Operation of 5-Phase Induction Motor Drives using DTC Techniques | Bermudez Guzman, Mario

Open-Phase Fault Operation of 5-Phase Induction Motor Drives using DTC Tech...

Archive ouverte: Communication dans un congrès

Bermudez Guzman, Mario | 2015-11

International audience. Direct torque control (DTC) is extensively used in conventional three-phase drives as an alternative to field-oriented control methods. The standard DTC technique was originally designed to r...

Open-Phase Fault-Tolerant Direct Torque Control Technique for Five-Phase Induction Motor Drives | Bermudez Guzman, Mario

Open-Phase Fault-Tolerant Direct Torque Control Technique for Five-Phase In...

Archive ouverte: Article de revue

Bermudez Guzman, Mario | 2017

International audience. Direct torque control (DTC) has been widely used as an alternative to traditional field-oriented control (FOC) methods for three-phase drives. The conventional DTC scheme has been successfull...

Comparative Study of DTC and RFOC Methods for the Open-Phase Fault Operation of a 5-Phase Induction Motor Drive | Bermudez, Mario

Comparative Study of DTC and RFOC Methods for the Open-Phase Fault Operatio...

Archive ouverte: Communication dans un congrès

Bermudez, Mario | 2015-11

International audience. Direct Torque Control (DTC) technique has been applied in recent times in high performance five-phase induction motor drives during the normal operation of the system. The use of DTC in the m...

An Experimental Assessment of Open-Phase Fault-Tolerant Virtual-Vector-Based Direct Torque Control in Five-Phase Induction Motor Drives | Bermudez Guzman, Mario

An Experimental Assessment of Open-Phase Fault-Tolerant Virtual-Vector-Base...

Archive ouverte: Article de revue

Bermudez Guzman, Mario | 2017

International audience. Direct torque control (DTC) has been recently used for the development of high-performance five-phase induction motor (IM) drives, where normal operation of the system has been usually consid...

Fault tolerant control with delays systems: Application to a PEMFC system | Bougatef, Zina

Fault tolerant control with delays systems: Application to a PEMFC system

Archive ouverte: Communication dans un congrès

Bougatef, Zina | 2020-11-24

International audience. he problem of active Fault Tolerant Control (FTC) for a Polymer Electrolyte Membrane Fuel Cell (PEMFC) systems with time delays subject to an actuator fault, is investigated in this paper. Th...

Torque Optimization of a Seven-Phase Bi-harmonic PMSM in Healthy and Degraded Mode | Zhang, Hao

Torque Optimization of a Seven-Phase Bi-harmonic PMSM in Healthy and Degrad...

Archive ouverte: Communication dans un congrès

Zhang, Hao | 2019-08-11

International audience. Compared to sinusoidal machines, a bi-harmonic machine (with only two harmonics of similar value in the electromotive force spectrum) can develop torque of comparable values under three kinds...

Chargement des enrichissements...