Comparison and Analysis of Post-Fault Operation Modes in a Five-Phase PMSM Considering Thermal Behavior

0 avis

Comparison and Analysis of Post-Fault Operation Modes in a Five-Phase PMSM Considering Thermal Behavior

Archive ouverte : Communication dans un congrès

Zahr, Hussein | Trabelsi, Mohamed | Semail, Eric

International audience. This paper presents a comparative evaluation of fault tolerant control strategies for a five-phase Permanent Magnet Synchronous Machine (PMSM) under an opened-phasefault mode. Two main classical Fault Tolerant Control (FTC) methods and the no-reconfiguration strategy are compared with the normal mode operation considering peak current, peak voltage, average torque, torque ripples and measured temperatures of five windings of the five phases. The analysis of the temperature repartition shows that, in fault mode, at least in the particular studied case, the knowledge of the Joule losses is not sufficient for a correct control of the temperature.

Langue: Anglais

Date de publication: 2018-04-10

Source: : 2018 IEEE 12th International Conference on Compatibility, Power Electronics and Power Engineering (CPE-POWERENG 2018)

Sujets

Consulter en ligne

Consulter le document

Suggestions

Du même auteur

Design Considerations of Five-Phase Machine with Double p/3p Polarity

Archive ouverte: Article de revue

Gong, Jinlin | 2018

International audience. In the context of traction drives with required torque transient capabilities and a classically wide flux weakening speed range, this paper gives design considerations of a particularDouble-P...

Homopolar Current’s Copper Losses Analysis for Different Modulations in Ope...

Archive ouverte: Communication dans un congrès

dos Santos Moraes, Tiago José | 2018-09-03

International audience. This paper analyses the copper losses due to the homopolar current of a five-phase open-end winding machine supplied by a 10-leg inverter and a single DC voltage source. This topology can hav...

Five-Phase Bi-Harmonic PMSM Control under Voltage and Currents Limits

Archive ouverte: Communication dans un congrès

Zahr, Hussein | 2017-10

International audience. For a particular five-phase synchronous machine, this paper investigates the sensitivity of a vectorial control strategy on the required peak phase voltage whose value is fundamental for the ...

Du même sujet

Fault tolerant control with delays systems: Application to a PEMFC system

Archive ouverte: Communication dans un congrès

Bougatef, Zina | 2020-11-24

International audience. he problem of active Fault Tolerant Control (FTC) for a Polymer Electrolyte Membrane Fuel Cell (PEMFC) systems with time delays subject to an actuator fault, is investigated in this paper. Th...

Fault-Tolerant Control for Non-sinusoidal Seven-phase PMSMs with Similar Co...

Archive ouverte: Communication dans un congrès

Vu, Duc Tan | 2022-07-27

International audience. This paper proposes a strategy using new transformation matrices to calculate new current references when a non-sinusoidal seven-phase permanent magnet synchronous machine (PMSM) has an open-...

Fault-tolerant Control for Non-sinusoidal Multiphase Drives with Minimum To...

Archive ouverte: Article de revue

Vu, Duc Tan | 2021-12-09

International audience. For non-sinusoidal electromotive force (NS-EMF) multiphase machines, this paper proposes a new strategy and control scheme to guarantee smooth torque under an open-phase fault. Notably, the c...

Fault Tolerant Control of a Seven-phase Drive by Degrees of Freedom Adaptat...

Archive ouverte: Communication dans un congrès

Kestelyn, Xavier | 2010-03

La version éditeur est disponible à l'adresse suivante : http://ieeexplore.ieee.org/stamp/stamp.jsp?tp=&arnumber=5472476&isnumber=5472440. International audience. This paper proposes a simple way to control multi-ph...

Fault-tolerant Control for 7-phase Non-sinusoidal Permanent Magnet Machines...

Archive ouverte: Communication dans un congrès

Yanagihara, Keitaro | 2019-10-10

International audience. This paper presents new fault-tolerant control strategies for field-oriented control of 7-phase non-sinusoidal permanent magnet (PM) machines supplied by voltage source inverters (VSI). Singl...

Active fault tolerant control of wind turbine systems based on DFIG with ac...

Archive ouverte: Article de revue

Li, Shanzhi | 2018

International audience. This paper presents an active fault tolerant control (FTC) for doubly fed induction generator (DFIG) with actuator fault and disturbance using Takagi-Sugeno(TS) fuzzy model. The control struc...

Chargement des enrichissements...