Torque optimization of seven phase BLDC machines in normal and degraded modes with constraints on current and voltage | Vu, Duc Tan
/5

0 avis

Torque optimization of seven phase BLDC machines in normal and degraded modes with constraints on current and voltage

Archive ouverte : Communication dans un congrès

Vu, Duc Tan | Nguyen, Ngac Ky | Semail, Eric | dos Santos Moraes, Tiago José

Edité par HAL CCSD

International audience. This paper proposes several easy-to-implement control strategies when seven-phase axial flux brushless DC machines with trapezoidal back electromotive forces operate in normaland faulty modes by taking into account constraints on voltage and current. The constraints are related to the converter and machine design in terms of maximum values of current andvoltage. The considered faults are cases in which one or two phases of the machine are open-circuited. Numerical computations based on analytical formulations are applied toobtain torque-speed characteristics, including the fluxweakening operation. The methods determine current references to ensure the torque optimizations while currents and voltages are within their limits. The usefulness of the methods is verified by numerical results.

Consulter en ligne

Suggestions

Du même auteur

Fault-tolerant control of non-sinusoidal multiphase permanent magnet synchronous machine drives under constraints on current and voltage for automotive applications. Commande tolérante aux défauts des entraînements de machines synchrones à aimants permanents polyphasées non-sinusoïdales sous contraintes de courant et de tension pour les applications automobiles | Vu, Duc Tan

Fault-tolerant control of non-sinusoidal multiphase permanent magnet synchr...

Archive ouverte: Thèse

Vu, Duc Tan | 2020-11-24

Electric drives for electrified vehicles need to fulfil some specific requirements from automotive markets such as high efficiency, high volume power and torque densities, low-cost but safe-to-touch, high functional reliability, h...

An Overview of Methods using Reduced-Ordered Transformation Matrices for Fault-Tolerant Control of 5-phase Machines with an Open Phase | Vu, Duc Tan

An Overview of Methods using Reduced-Ordered Transformation Matrices for Fa...

Archive ouverte: Communication dans un congrès

Vu, Duc Tan | 2019-02-13

International audience. This paper studies control strategies using modified transformation matrices when five-phase machines operate in oneopen-phase faults. The basic idea of these methods is to maintain the rotat...

Fault-tolerant Control for Non-sinusoidal Multiphase Drives with Minimum Torque Ripple | Vu, Duc Tan

Fault-tolerant Control for Non-sinusoidal Multiphase Drives with Minimum To...

Archive ouverte: Article de revue

Vu, Duc Tan | 2021-12-09

International audience. For non-sinusoidal electromotive force (NS-EMF) multiphase machines, this paper proposes a new strategy and control scheme to guarantee smooth torque under an open-phase fault. Notably, the c...

Du même sujet

Real-Time Validation of a Cascaded Model Predictive Control Technique for a Five-Phase Permanent Magnet Synchronous Machine Under Current and Voltage Limits | Bermudez Guzman, Mario

Real-Time Validation of a Cascaded Model Predictive Control Technique for a...

Archive ouverte: Communication dans un congrès

Bermudez Guzman, Mario | 2017-07

International audience. Multiphase machines have recently gained importance in the research community for their use in applications where high power density, wide speed range and fault-tolerant capabilities are need...

Fault tolerant control with delays systems: Application to a PEMFC system | Bougatef, Zina

Fault tolerant control with delays systems: Application to a PEMFC system

Archive ouverte: Communication dans un congrès

Bougatef, Zina | 2020-11-24

International audience. he problem of active Fault Tolerant Control (FTC) for a Polymer Electrolyte Membrane Fuel Cell (PEMFC) systems with time delays subject to an actuator fault, is investigated in this paper. Th...

Model predictive optimal control considering current and voltage limitations: Real-time validation using OPAL-RT technologies and five-phase permanent magnet synchronous machines | Bermudez Guzman, Mario

Model predictive optimal control considering current and voltage limitation...

Archive ouverte: Article de revue

Bermudez Guzman, Mario | 2019-04

International audience. Multiphase machines have recently gained interest in the research community for their use in applications where high power density, wide speed range and fault-tolerant capabilities are requir...

Torque Optimization of a Seven-Phase Bi-harmonic PMSM in Healthy and Degraded Mode | Zhang, Hao

Torque Optimization of a Seven-Phase Bi-harmonic PMSM in Healthy and Degrad...

Archive ouverte: Communication dans un congrès

Zhang, Hao | 2019-08-11

International audience. Compared to sinusoidal machines, a bi-harmonic machine (with only two harmonics of similar value in the electromotive force spectrum) can develop torque of comparable values under three kinds...

Active fault tolerant control of wind turbine systems based on DFIG with actuator fault and disturbance using Takagi-Sugeno fuzzy model | Li, Shanzhi

Active fault tolerant control of wind turbine systems based on DFIG with ac...

Archive ouverte: Article de revue

Li, Shanzhi | 2018

International audience. This paper presents an active fault tolerant control (FTC) for doubly fed induction generator (DFIG) with actuator fault and disturbance using Takagi-Sugeno(TS) fuzzy model. The control struc...

Comparison of five-phase, six-phase and seven-phase fault tolerant electric drives | Ribiere, Antonin

Comparison of five-phase, six-phase and seven-phase fault tolerant electric...

Archive ouverte: Communication dans un congrès

Ribiere, Antonin | 2022-06

International audience. Automotive industry is evolving towards more fault-tolerant actuators to fulfill future autonomous vehicles requirements. Critical applications such as steering or braking have to resist to f...

Chargement des enrichissements...